When Emacs visits a file, it automatically selects a major mode for the buffer based on information in the file name or in the file itself. It also processes local variables specified in the file text.
This function establishes the proper major mode and buffer-local
variable bindings for the current buffer. It calls
set-auto-mode
(see below). As of Emacs 26.1, it no longer
runs hack-local-variables
, this now being done in
run-mode-hooks
at the initialization of major modes
(see Mode Hooks).
If the find-file argument to normal-mode
is non-nil
,
normal-mode
assumes that the find-file
function is calling
it. In this case, it may process local variables in the ‘-*-’
line or at the end of the file. The variable
enable-local-variables
controls whether to do so. See Local Variables in Files in The GNU Emacs Manual,
for the syntax of the local variables section of a file.
If you run normal-mode
interactively, the argument
find-file is normally nil
. In this case,
normal-mode
unconditionally processes any file local variables.
The function calls set-auto-mode
to choose and set a major
mode. If this does not specify a mode, the buffer stays in the major
mode determined by the default value of major-mode
(see below).
normal-mode
uses condition-case
around the call to the
major mode command, so errors are caught and reported as a ‘File
mode specification error’, followed by the original error message.
This function selects and sets the major mode that is appropriate
for the current buffer. It bases its decision (in order of
precedence) on the ‘-*-’ line, on any ‘mode:’ local
variable near the end of a file, on the ‘#!’ line (using
interpreter-mode-alist
), on the text at the beginning of the
buffer (using magic-mode-alist
), and finally on the visited
file name (using auto-mode-alist
). See How
Major Modes are Chosen in The GNU Emacs Manual. If
enable-local-variables
is nil
, set-auto-mode
does
not check the ‘-*-’ line, or near the end of the file, for
any mode tag.
There are some file types where it is not appropriate to scan the file
contents for a mode specifier. For example, a tar archive may happen to
contain, near the end of the file, a member file that has a local
variables section specifying a mode for that particular file. This
should not be applied to the containing tar file. Similarly, a tiff
image file might just happen to contain a first line that seems to
match the ‘-*-’ pattern. For these reasons, both these file
extensions are members of the list inhibit-local-variables-regexps
.
Add patterns to this list to prevent Emacs searching them for local
variables of any kind (not just mode specifiers).
If keep-mode-if-same is non-nil
, this function does not
call the mode command if the buffer is already in the proper major
mode. For instance, set-visited-file-name
sets this to
t
to avoid killing buffer local variables that the user may
have set.
This function sets the major mode of buffer to the default value of
major-mode
; if that is nil
, it uses the
current buffer’s major mode (if that is suitable). As an exception,
if buffer’s name is *scratch*, it sets the mode to
initial-major-mode
.
The low-level primitives for creating buffers do not use this function,
but medium-level commands such as switch-to-buffer
and
find-file-noselect
use it whenever they create buffers.
The value of this variable determines the major mode of the initial
*scratch* buffer. The value should be a symbol that is a major
mode command. The default value is lisp-interaction-mode
.
This variable specifies major modes to use for scripts that specify a
command interpreter in a ‘#!’ line. Its value is an alist with
elements of the form (regexp . mode)
; this says to
use mode mode if the file specifies an interpreter which matches
\\`regexp\\'
. For example, one of the default elements
is ("python[0-9.]*" . python-mode)
.
This variable’s value is an alist with elements of the form
(regexp . function)
, where regexp is a
regular expression and function is a function or nil
.
After visiting a file, set-auto-mode
calls function if
the text at the beginning of the buffer matches regexp and
function is non-nil
; if function is nil
,
auto-mode-alist
gets to decide the mode.
This works like magic-mode-alist
, except that it is handled
only if auto-mode-alist
does not specify a mode for this file.
This variable contains an association list of file name patterns
(regular expressions) and corresponding major mode commands. Usually,
the file name patterns test for suffixes, such as ‘.el’ and
‘.c’, but this need not be the case. An ordinary element of the
alist looks like (regexp . mode-function)
.
For example,
(("\\`/tmp/fol/" . text-mode) ("\\.texinfo\\'" . texinfo-mode) ("\\.texi\\'" . texinfo-mode)
("\\.el\\'" . emacs-lisp-mode) ("\\.c\\'" . c-mode) ("\\.h\\'" . c-mode) …)
When you visit a file whose expanded file name (see Functions that Expand Filenames), with version numbers and backup suffixes removed using
file-name-sans-versions
(see File Name Components), matches
a regexp, set-auto-mode
calls the corresponding
mode-function. This feature enables Emacs to select the proper
major mode for most files.
If an element of auto-mode-alist
has the form (regexp
function t)
, then after calling function, Emacs searches
auto-mode-alist
again for a match against the portion of the file
name that did not match before. This feature is useful for
uncompression packages: an entry of the form ("\\.gz\\'"
function t)
can uncompress the file and then put the uncompressed
file in the proper mode according to the name sans ‘.gz’.
If auto-mode-alist
has more than one element whose regexp
matches the file name, Emacs will use the first match.
Here is an example of how to prepend several pattern pairs to
auto-mode-alist
. (You might use this sort of expression in your
init file.)
(setq auto-mode-alist (append ;; File name (within directory) starts with a dot. '(("/\\.[^/]*\\'" . fundamental-mode) ;; File name has no dot. ("/[^\\./]*\\'" . fundamental-mode) ;; File name ends in ‘.C’. ("\\.C\\'" . c++-mode)) auto-mode-alist))