#
# Section Chassis_Front_Panel_Buttons Comments 
#
# The following configuration options are for enabling or disabling button 
# functionality on the chassis. Button may refer to a pushbutton, switch, or 
# other front panel control built into the system chassis. 
#
# The value of the below may not be able to be checked out. Therefore we 
# recommend the user configure all four fields rather than a subset of them, 
# otherwise some assumptions on configure may be made. 
#
Section Chassis_Front_Panel_Buttons
	## Possible values: Yes/No
	Enable_Standby_Button_For_Entering_Standby    Yes
	## Possible values: Yes/No
	Enable_Diagnostic_Interrupt_Button            Yes
	## Possible values: Yes/No
	Enable_Reset_Button                           Yes
	## Possible values: Yes/No
	Enable_Power_Off_Button_For_Power_Off_Only    Yes
EndSection
#
# Section Chassis_Power_Conf Comments 
#
# The following configuration options are for configuring chassis power 
# behavior. 
#
# The "Power_Restore_Policy" determines the behavior of the machine when AC 
# power returns after a power loss. The behavior can be set to always power on 
# the machine ("On_State_AC_Apply"), power off the machine 
# ("Off_State_AC_Apply"), or return the power to the state that existed before 
# the power loss ("Restore_State_AC_Apply"). 
#
# The "Power_Cycle_Interval" determines the time the system will be powered down 
# following a power cycle command. 
#
Section Chassis_Power_Conf
	## Possible values: Off_State_AC_Apply/Restore_State_AC_Apply/On_State_AC_Apply
	Power_Restore_Policy                          Off_State_AC_Apply
	## Give value in seconds
	## Power_Cycle_Interval                       
EndSection
#
# Section Chassis_Boot_Flags Comments 
#
# The following configuration options are for configuring chassis boot behavior. 
# Please note that some fields may apply to all future boots while some may only 
# apply to the next system boot. 
#
# "Boot_Flags_Persistent" determines if flags apply to the next boot only or all 
# future boots. 
#
# "Boot_Device" allows the user to configure which device the BIOS should boot 
# off of. Most users may wish to select NO-OVERRIDE to select the configuration 
# currently determined by the BIOS. Note that the configuration value BIOS-SETUP 
# refers to booting *into* the BIOS Setup, not from it. FLOPPY may refer to any 
# type of removeable media. 
#
Section Chassis_Boot_Flags
	## Possible values: Yes/No (Yes = All Future Boots; No = Next Boot Only)
	Boot_Flags_Persistent                         Yes
	## Possible values: PC-COMPATIBLE/EFI
	BIOS_Boot_Type                                PC-COMPATIBLE
	## Possible values: Yes/No (Only applies to Next Boot)
	CMOS_Clear                                    No
	## Possible values: Yes/No (Only applies to Next Boot)
	Lock_Keyboard                                 No
	## Possible values: Yes/No (Only applies to Next Boot)
	Screen_Blank                                  No
	## Possible values: NO-OVERRIDE/PXE/HARD-DRIVE/HARD-DRIVE-SAFE-MODE/
	##                  DIAGNOSTIC_PARTITION/CD-DVD/BIOS-SETUP/FLOPPY
	Boot_Device                                   NO-OVERRIDE
	## Possible values: Yes/No
	Lock_Out_Reset_Button                         No
	## Possible values: Yes/No
	Lock_Out_Power_Button                         No
	## Possible values: Yes/No
	Lock_Out_Sleep_Button                         No
	## Possible values: DEFAULT/QUIET/VERBOSE
	Firmware_Bios_Verbosity                       DEFAULT
	## Possible values: Yes/No
	Force_Progress_Event_Traps                    No
	## Possible values: Yes/No
	User_Password_Bypass                          No
	## Possible values: BIOS-SETTING/SUPPRESS/ENABLE
	Console_Redirection                           BIOS-SETTING
EndSection
